Prof. Martin O. Saar, ETH Zurich
1 September 2012
NSF Sustainable Energy Pathways Funding Nr SEP-1230691
Prof. Martin O. Saar, ETH Zurich
CO2 Plume Geothermal systems (CPG) (Randolph and Saar, 2011a, b; Saar et al., 2012; Buscheck et al., 2013), involve injection of CO2 that comes from a CO2 emitter, as a working fluid to extract heat and pressure energy (enthalpy) from naturally high-permeability sedimentary or stratigraphic basins. The injected CO2 forms a large subsurface CO2 plume that permanently sequesters CO2 underground and absorbs heat from the geothermal reservoir. The CO2 plume can be “tapped” for thermal and/or electric power production in a geothermal power system (Randolph and Saar, 2011a; Saar et al., 2012; Adams et al., 2014, 2015). The heat density of sedimentary basins is typically relatively low. However, this drawback can be counteracted by the large accessible volume of natural reservoirs compared to the relatively artificial small reservoirs developed by hydro-fracturing (Dezayes et al., 2005). Furthermore, supercritical CO2 has a high mobility (i.e., low kinematic viscosity) and high thermal expansibility compared to water, resulting in the formation of a strong thermosiphon, which eliminates the need for parasitic pumping power requirements. The thermosiphon effect significantly increases the electric power production efficiency of the geothermal system compared to water-based geothermal systems. The produced power can then, for example, be used to drive the CO2 injection pumps if geologic CO2 is ongoing and/or it could be supplied to the electric grid. Because the produced CO2 is reinjected into the geothermal reservoir with the main CO2 sequestration stream, coming from the CO2 emitter, all of the CO2 is ultimately geologically sequestered resulting in a CO2 sequestering geothermal power plant with a negative carbon footprint. Alternatively, when geologic CO2 storage is uneconomic, CPG systems could also be operated with a limited, finite amount of CO2 stored underground and thereafter run with little or no additional makeup CO2. Such scenarios are investigated in this project.
In keeping with the objective of formulating a simple model to gain first-order insights, we assume a homogeneous reservoir with a symmetrical CO2 plume formation around the vertical injection well. Therefore, a two-dimensional axisymmetric numerical model is formulated in cylindrical coordinates, representing a reservoir initially filled with native brine, that is gradually displaced by the injected, supercritical CO2. The CO2 enters the reservoir through a vertical, injection well. After moving through the geothermal reservoir, the heated CO2 is produced from a horizontal, circular production well (Noble, 1992; Gardes, 1995, 1998).We characterize the performance of such a CPG system as a function of heat energy output from the reservoir, reservoir lifespan or longevity given as reservoir temperature decline over time, and up-coning of the brine-CO2 interface into the inlet of the production well. The numerical simulator employed is TOUGH2 (Pruess et al., 1999; Pruess, 2004) with the equation of state (EOS) modules ECO2N (Pruess, 2005) and ECO2H (Spycher and Pruess, 2011), for reservoir temperatures at/below and above T=100°C, respectively. In this study the CPG system is operated in two stages, during the first stage CO2 is injected into the reservoir to develop sufficient CO2 plume formation by displacing brine between injection and production wells . During the second stage, the geothermally heated CO2 is produced and circulated to generate power.
- The finite amount of initially injected CO2 required to operate a CPG system increases with increasing well spacing between injection and production wells, and reservoir depth, and decreases for locations with higher geothermal gradients.
- The shape of the CO2 plume depends on the permeability of the reservoir. Hence, permeability heterogeneity have a considerable effect on the performance of a CO2 Plume Geothermal (CPG) system.
- Reservoir heat depletion rates decrease with increase in well spacing between injection and production wells.
- Reservoir depletion is slow for thick reservoirs and moderate depths (2.5 km).
- Reservoir depletes at a faster rate at higher geothermal gradients.
REFEREED PUBLICATIONS IN JOURNALS